Chemical Engineering Basics Quiz 6
1 / 50
In _________ process, there is an increase in entropy with no degradation of energy ?
2 / 50
In electrical resistance welding, distortion results from the use of improper_________?
3 / 50
In a drilling process, the metal is removed by both shearing & extrusion. General purpose drills are made of__________?
4 / 50
In chemical dehumidification of air_____?
5 / 50
In a good rimming steel___________?
6 / 50
In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will ________?
7 / 50
In a furnace with heating element temperature at 1700?C, the dominant mechanism of heat transfer will be___________?
8 / 50
Heating the Hypo-eutectoid steels to 30?C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called_________?
9 / 50
Identify the false statement?
10 / 50
Hot extrusion of aluminium is done in the temperature range of _________ ?C ?
11 / 50
In case of a, centrifugal pump, the ratio h1/h2 is termed as the ______ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller)?
12 / 50
Hot & cold working of material causes its ________ deformation?
13 / 50
Heating of ferromagnetic materials to a temperature above Curie temperature makes it __________?
14 / 50
In connection with corrosion of metals, passivation is the process that___________?
15 / 50
If Reynolds number is greater than 1, then the_______?
16 / 50
In the Bayer?s process, bauxite is digested under pressure using _____?
17 / 50
In inventory control theory, the economic order quantity (EOQ) is the______?
18 / 50
In practice, the compression ratio of compression-ignition (CI) engine ranges from ________?
19 / 50
If the head is doubled in & centrifugal pump, the power required will increase in the ratio of___________?
20 / 50
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by__________?
21 / 50
In multipass welds, shot peening is done after each pass to___________?
22 / 50
If a nuclear reactor produces more fissile nuclear fuel than it consumes, then it is called a ______ reactor?
23 / 50
In case of condensers & evaporators operating under given terminal conditions, LMTD (logarithmic mean temperature difference) for counter flow as compared to that for parallel flow is___________?
24 / 50
Hot working of lead is carried out at _____?
25 / 50
Highest cutting speed is achieved by the ________ tool material ?
26 / 50
In case of simple harmonic motion, displacement is proportional to the__________?
27 / 50
High endurance limit of carburised machine parts is because of the fact that carburisation ___________?
28 / 50
If the demand for an item is trebled and the order cost is reduced to one third, then the economic order quantity__________?
29 / 50
In Newton?s law of viscosity, which states that the shear stress is proportional to the ______ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, Vg = velocity gradient) ?
30 / 50
In condensers used in thermal power plants, steam is normally used in shell side and cooling water on the tube side, because of the reason that ?
31 / 50
Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by ______ have residual stresses ?
32 / 50
In case of water (Prandtl number ? 6) flowing over a flat plate heated over the entire length, the thermal boundary layer thickness as compared to hydrodynamic boundary layer thickness is ?
33 / 50
In the blast furnace, incorporation of water vapour in the blast gives the following effect ?
34 / 50
In a forced draft cooling tower, water is cooled from 95 to 80?F by exposure to air with a wet bulb temperature of 70?F. In this case, the_________?
35 / 50
In ?Imperial Smelting Process? for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following _________?
36 / 50
Identify the correct statement with reference to the extractive metallurgy of aluminium ?
37 / 50
In a neutral solution___________?
38 / 50
In extrusion of metals, which of the following statement is true ?
39 / 50
In the diving apparatus, helium is used along with oxygen, because it is ______?
40 / 50
Hydrogen in liquid steels is dissolved__________?
41 / 50
In case of brasses, with decreasing zinc percentage and increasing copper percentage, its ______ increases ?
42 / 50
In the acid Bessemer process, the hot metal should have the following composition ?
43 / 50
Hydro-cyclone is a______?
44 / 50
High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27?C with relative humidity ranging from ________ percent ?
45 / 50
Hooke?s law_________?
46 / 50
In a totally irreversible isothermal expansion process for an ideal gas, ?E = 0, ?H = 0. Then ?Q and ?S will be________?
47 / 50
Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process ?
48 / 50
Heat transfer by _______ is almost absent in case of fluidised bed drying operation?
49 / 50
High speed steel tools retain their hardness upto a temperature of ___________ ?C?
50 / 50
If a solid is compressed adiabatically in its elastic range, its ______ remains constant ?
Provide Your Information
Your score is
The average score is 8%
Restart quiz
