Mechanical Engineering Quiz 10
1 / 50
Kinematic viscosity is equal to_________________?
2 / 50
In order that a cycle be reversible, following must be satisfied ________________?
3 / 50
Thermal conductivity of wood depends on_______________?
4 / 50
The compression ratio in a gas turbine is of the roder of____________________?
5 / 50
Solids and liquids have___________________?
6 / 50
Connecting rod is usually made of_________________?
7 / 50
A neutral flame is obtained by supplying___________________?
8 / 50
Pick up the correct statement about relationship between various floats______________________?
9 / 50
The pour point of diesel oil must be_________________?
10 / 50
I.S. specifies following total number of grades of tolerances__________________?
11 / 50
Monte Carlo solutions in queuing theory are extremely useful in queuing problems_________________?
12 / 50
The metallic structure of mild steel is_________________?
13 / 50
Inventory control in production, planning and control aims at________________?
14 / 50
Francis turbine is best suited for_____________________?
15 / 50
Efficiency of a riveted joint is the ratio of its strength (max. load it can resist without failure) to the strength of the unpunched plate in_________________?
16 / 50
Which tool is used to measure gap size in a rough alignment?
17 / 50
Structural steel contains following principal alloying elements__________________?
18 / 50
Which is correct statement about reaction time for autoignition of fuel and the fuel air ratio__________________?
19 / 50
Pulverized fuel is used for___________________?
20 / 50
In PERT analysis, critical path is obtained by joining events having___________________?
21 / 50
Gnatt charts are used for_________________?
22 / 50
Kinematic pairs are those which have two elements that ______________?
23 / 50
The ultimate tensile strength of low carbon steel by working at a high strain rate will_________________?
24 / 50
The normal stress is same in all directions at a point in a fluid_______________?
25 / 50
Which of the following is independent of sales forecast______________?
26 / 50
Auto-ignition reaction time for petrol engine first decreases with increase in fuel air ratio, reaches a minimum value and then increases with subsequent increase in fuel air ratio. The minimum value occurs in the region of________________?
27 / 50
Amongst the following, the fissionable materials are________________?
28 / 50
Wrought iron is________________?
29 / 50
The efficiency of a nuclear power plant in comparsion to a conventional thermal power plant is________________?
30 / 50
In axial flow fans and turbines, fluid enters and leaves as follows________________?
31 / 50
Corioli?s component of acceleration exists whenever a point moves along a path that has________________?
32 / 50
In vapor compression refrigeration system, refrigerant occurs as liquid between_________________?
33 / 50
Blast furnace produces following by reduction of iron ore_______________?
34 / 50
A key is subjected to side pressure as well at shearing forces. These pressures are called_________________?
35 / 50
A diesel engine has_________________?
36 / 50
In actual machines_____________________?
37 / 50
As a result of detonation in an I.C engine, following parameter attains very high value _____________________?
38 / 50
A trolley wire weighs 1.2 kg per meter length. The ends of the wire are attached to two poles 20 meters apart. If the horizontal tension is 1500 kg find the dip in the middle of the span___________________?
39 / 50
Turn buckle has____________________?
40 / 50
Elastic nut is a locking device in which__________________?
41 / 50
Free air is the air at________________?
42 / 50
Inertia force acts___________________?
43 / 50
In which case the air-fuel ratio is likely to be maximum _________________?
44 / 50
Which of the following parameters is constant for a mole for most of the gases at a given temperature and pressure___________________?
45 / 50
The composition of silver solder is ___________________?
46 / 50
A diesel engine as compared to petrol engine (both running ar rated load) is ____________________?
47 / 50
Petrol is distilled at a temperature in range of__________________?
48 / 50
The Ackermann steering mechanism is preferred to the Davis type in automobiles because____________________?
49 / 50
On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be___________________?
50 / 50
Pick up the wrong statement?
Provide Your Information
Your score is
The average score is 60%
Restart quiz
