Civil Engineering Quiz 48
1 / 50
The hourly variation factor is usually taken as_____?
2 / 50
Updating may result in________?
3 / 50
On a single lane road with two way traffic, the minimum stopping sight distance is equal to_____?
4 / 50
The length of clear zone for none instrument runway of a small aircraft is_______?
5 / 50
A square surface 3 m x 3 m lies in a vertical line in water pipe its upper edge at vater surface. The hydrostatic force on square surface is _________?
6 / 50
The sewerage system originates from_________?
7 / 50
Highway facilities are designed for________?
8 / 50
Whenever an activity has zero total float, then______?
9 / 50
A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m2 when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45?. The values of cohesion and angle of internal friction for the soil are respectively_____________?
10 / 50
Infiltration capacity________?
11 / 50
Select the correct statement ?
12 / 50
A cube on a smooth horizontal surface__________?
13 / 50
During the first stage of triaxial test when the cell pressure is increased from 0.10 N/mm2 to 0.26 N/mm2, the pore water pressure increases from 0.07 N/mm2 to 0.15 ?N/mm2. Skempton?s pore pressure parameter B is__________?
14 / 50
Which of the following is not a PERT event ?
15 / 50
For a given velocity of a projectile, the range is maximum when the angle of projection is__________?
16 / 50
Number of cotters used in CST-9 sleepers is_________?
17 / 50
If y is force and x is velocity, then dimensions of ?=r are dx2_________?
18 / 50
The carryover factor in a prismatic member whose far end is fixed is__________?
19 / 50
Pick up the correct statement from the following?
20 / 50
If the formation level of a highway has a uniform gradient for a particular length, and the ground is also having a longitudinal slope, the earthwork may be calculated by______?
21 / 50
The minimum and maximum diameters of sewers shall preferably be________?
22 / 50
In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is_________?
23 / 50
Effects of shear force and axial force on plastic moment capacity of a structure are respectively to________?
24 / 50
Select the correct statement_________?
25 / 50
The distribution mains are designed for_______?
26 / 50
Paints with white lead base are suitable for painting of_____________?
27 / 50
A sphere and a cylinder having the same mass and radii start from rest and roll down the same inclined plane. Which body gets to the bottom first ?
28 / 50
Compressibility of sandy soils is_____?
29 / 50
The function of cleats in a roof truss is_____?
30 / 50
With the increase in the quantity of water supplied, the yield of most crops________?
31 / 50
The flow in which conditions do not change with time at any point, is known as ____________?
32 / 50
The dissolved oxygen level in natural unpolluted waters at normal temperature is found to be of the order of_______?
33 / 50
What type of bond whose guaranty is in lien on railroad equipment, such as freight and passenger cars, locomotives, etc ?
34 / 50
In the double application of principle of reversion, the apparent error is______?
35 / 50
When the bituminous surfacing is done on already existing black top road or over existing cement concrete road, the type of treatment to be given is_______?
36 / 50
Leaf reflectance depends primarily on_____?
37 / 50
Pick up the correct statement from the following ?
38 / 50
A divide wall is provided______?
39 / 50
Number of keys used in CST-9 sleeper is________?
40 / 50
The length of lap in tension reinforcement should not be less than the bar diameter ? (actual tension / four times the permissible average bond stress) if it is more than______?
41 / 50
The ?centre line method? is specially adopted for estimating________?
42 / 50
P = /4L? is the equation of Euler?s crippling load, if_________?
43 / 50
Bottom most layer of pavement is known as_____________?
44 / 50
In Belgium method of tunneling ________?
45 / 50
In plastic analysis, the shape factor for rectangular section, is_______?
46 / 50
The shear stress distribution for a fluid flowing in between the parallel plates, both at rest, is______?
47 / 50
per unit run exerted by the Total pressure on the vertical face of a retaining wall of height retained earth weighing per unit volume, is__________?
48 / 50
The type of roof suitable in plains where rainfall is meagre and temperature is high is_____?
49 / 50
An aggrading river is a________?
50 / 50
If the weight of a body immersed in a fluid exceeds the buoyant force, then the body will_______?
Provide Your Information
Your score is
The average score is 0%
Restart quiz
