Home » Chemical Engineering Quiz » Chemical Engineering Basics Quiz 10

Chemical Engineering Basics Quiz 10

0%
0

Chemical Engineering Basics Quiz 10

1 / 50

Stainless steel is welded with difficulty because of______?

2 / 50

The ability of tool steel to resist softening at high temperatures is termed as ___________ hardness?

3 / 50

Strain hardening effect in a metal subjected to cold working is due to the _______ mechanism?

4 / 50

Routing in production, planning & control is concerned with the_____?

5 / 50

Specific __________ is a dimensionless quantity ?

6 / 50

Sand used to stop the green sand from sticking to the pattern is termed as the _______ sand?

7 / 50

Stainless steel is welded using___________?

8 / 50

Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30% ?

9 / 50

Temperature attained in soldering of metals is about _________ ?C?

10 / 50

Square steel key is normally strong in failure by shear & crushing. Keys are normally made of ________ steel bars?

11 / 50

Specific gravity of a metal, which weighs 5 kg in air and 4 kg when submerged in water, will be_______?

12 / 50

Steel balls are manufactured by_______?

13 / 50

Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of _______ will facilitate the most accurate measurement of the temperature ?

14 / 50

Saturated steam at a pressure of 25 kg/cm2 is throttled to attain 5 kg/cm2. Then the outcoming steam will be__________?

15 / 50

Speisses is a mixture of the following ?

16 / 50

Softening of hardened steel is done by its______?

17 / 50

Satellite is a __________ material?

18 / 50

Steel & cast iron pipes are produced by _______ casting ?

19 / 50

Silicon in steel___________?

20 / 50

Steel produced from phosphatic iron is ________ in nature?

21 / 50

Specific gravity of hot metal (pig iron) is _______ times that of the blast furnace slag ?

22 / 50

Steel is welded using the _________ flame ?

23 / 50

Steel containing low percentage of nickel, chromium & tungsten are termed as the ______ steel ?

24 / 50

Silicon percentage in acid resistant cast iron is about _____?

25 / 50

The ?transition temperature? for ductile to brittle behavior of steel increases with increase in the ______ content in steel?

26 / 50

Suitability of steel for its use in cable is judged by its strength in___________?

27 / 50

Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode_________?

28 / 50

Screws are specified by their ______ diameters?

29 / 50

Spheroidising of a material is a/an _________ process?

30 / 50

Strain hardening effect in metals subjected to cold working is due to the ________ mechanism?

31 / 50

Shrinkage allowance on pattern is provided to compensate for shrinkage when the _______?

32 / 50

Steels with high carbon equivalent have poor Weldability, because in these steels during welding_________?

33 / 50

Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are ________ respectively ?

34 / 50

The ?laughing gas? is___________?

35 / 50

Shampoos are commercially not available in the form of _____?

36 / 50

Spherical shape of mercury droplets is due to its______?

37 / 50

Super heating of steam is done at constant_____?

38 / 50

Speed of a submarine in deep sea & that of an aeroplane is measured by a/an_____?

39 / 50

Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal__________?

40 / 50

Sub zero treatment of steel is done to______?

41 / 50

Super conduction in metals is observed at a temperature of _________ ?K?

42 / 50

Solidification time of a molten metal in a casting is proportional to (where, V = volume of metal & A = its surface area; in the casting) ?

43 / 50

Spark plug is provided in a/an__________?

44 / 50

Starting friction is low in case of the ______ lubrication?

45 / 50

Surface tension of a liquid__________?

46 / 50

Solute atoms which cause yield point phenomenon in mild steel are/is__________?

47 / 50

Tempering of a material does not improve its______?

48 / 50

Runge-Kutta method is used to solve a/an _____?

49 / 50

Sudden fall of atmospheric pressure by a large amount is an indication of the_______?

50 / 50

Stresses encountered in the metal forming processes are less than the ______ of the material?

Provide Your Information

Your score is

The average score is 0%

0%

Share on facebook
Facebook
Share on twitter
Twitter
Share on whatsapp
WhatsApp
Chemical Engineering Basics Quiz 1
Chemical Engineering Basics Quiz 2
Chemical Engineering Basics Quiz 3
Chemical Engineering Basics Quiz 4
Chemical Engineering Basics Quiz 5
Chemical Engineering Basics Quiz 6
Chemical Engineering Basics Quiz 7
Chemical Engineering Basics Quiz 8
Chemical Engineering Basics Quiz 9
Chemical Engineering Basics Quiz 11

Help Concept 360 Please. We need 500 Youtube Subscriber. Please Subscribe our Youtube Channel. Click below link to subscribe Please

آپ سے گزارش ہے کہ ہمارے یوٹیوب چینل کوسبسکرائب کر کے ہماری مدد کریں جیسا کہ یہ ویب سائٹ آپکی مدد کر رہی ہے۔ شکریہ