Home » Chemical Engineering Quiz » Chemical Engineering Basics Quiz 4

Chemical Engineering Basics Quiz 4

0%
0

Chemical Engineering Basics Quiz 4

1 / 50

Circular cross section machine parts which are symmetrical about the axis of rotation are made by hot_______?

2 / 50

Colour comparator is used to measure the_____?

3 / 50

Current employed in resistance welding ranges from ______ kVA/cm2?

4 / 50

Compressed dry air is used as the cutting fluid, while machining______?

5 / 50

Coarse grained steels have______?

6 / 50

Depreciation of machines fails under the indirect expenses head. As per income tax regulations, it is calculated by the ___________ method?

7 / 50

Electrical conductivities of semi-conductors are of the order of _______ ohm/cm ?

8 / 50

Cold chisel?s hammers are made of_____?

9 / 50

Corrosion rate cannot be lowered by reducing the _________ of the corroding medium?

10 / 50

Dryness fraction of dry steam is__________?

11 / 50

Cobalt ? 60 is used as a source of ______ in medical therapy & industrial radiography?

12 / 50

Electrometallurgical methods of metal extraction is normally used for those metals_____?

13 / 50

Common salt is produced from sea water in India generally by the _________ method?

14 / 50

Desalination of water___________?

15 / 50

Corrosion of metals cannot be prevented by its___________?

16 / 50

Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of ________ gms of zinc per m2 of steel strip ?

17 / 50

Damage to metal surface by mechanical action is called______?

18 / 50

Electrochemical corrosion can occur, only if _________ is present in contact with metal?

19 / 50

Copper deposits are found in India at the following location ?

20 / 50

Cold heading or upsetting is categorised as the _________ process ?

21 / 50

Consumable electrodes are used in the ______ welding?

22 / 50

Cupola produces __________ iron?

23 / 50

Co-efficient of performance of a Carnot cycle refrigerator operating between ? 23?C and + 27?C is _________?

24 / 50

Dislocation cross-slip is difficult in those materials, which have_____?

25 / 50

Cold working of a material results in increase in hardness, which is termed as the _______ hardening ?

26 / 50

Diamagnetic materials_____?

27 / 50

Constituents of stellite are ______?

28 / 50

During sensible heating of humid air___________?

29 / 50

Dephosphorization of molten pig iron is favoured by_________?

30 / 50

Cold cracking in the heat affected zone of a high strength steel weld can take place because of the_____?

31 / 50

Direct conversion of thermal energy to electrical energy is facilitated by the______?

32 / 50

Cold chisel & hammers are made of__________?

33 / 50

Dew point temperature always gives an indication of the ___________ of the moist air ?

34 / 50

During sensible cooling of air, its wet bulb temperature ?

35 / 50

During decarburising of a plain carbon steel, the thickness of ferrite layer growth is proportional to______?

36 / 50

Dies for wire drawing are generally made of___________?

37 / 50

Density in the solid state is slightly less than that in its liquid state, in case of______?

38 / 50

Dowtherm is a______?

39 / 50

Coating provided on the electrodes used in the arc welding is not expected to__________?

40 / 50

Closeness of packing is maximum in case of ______ crystal lattice?

41 / 50

Chlorine acts as a bleaching agent only in the presence of ________?

42 / 50

Corrosion is______?

43 / 50

Drossing is a _________ operation?

44 / 50

Difference at any instant between the value of the controlled variable and the set point is called the___________?

45 / 50

Chromium molybdenum steel cannot be welded using _______ welding ?

46 / 50

Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be _______ mm?

47 / 50

Diffusion co-efficient of a metal in a solid solution depends upon its ?

48 / 50

Earing is a defect found in steels after the following metal working operation ?

49 / 50

Dislocations are ________ defects?

50 / 50

Dry saturated steam can be converted into super heated steam by______?

Provide Your Information

Your score is

The average score is 0%

0%

Share on facebook
Facebook
Share on twitter
Twitter
Share on whatsapp
WhatsApp
Chemical Engineering Basics Quiz 1
Chemical Engineering Basics Quiz 2
Chemical Engineering Basics Quiz 3
Chemical Engineering Basics Quiz 5
Chemical Engineering Basics Quiz 6
Chemical Engineering Basics Quiz 7
Chemical Engineering Basics Quiz 8
Chemical Engineering Basics Quiz 9
Chemical Engineering Basics Quiz 10
Chemical Engineering Basics Quiz 11

Help Concept 360 Please. We need 500 Youtube Subscriber. Please Subscribe our Youtube Channel. Click below link to subscribe Please

آپ سے گزارش ہے کہ ہمارے یوٹیوب چینل کوسبسکرائب کر کے ہماری مدد کریں جیسا کہ یہ ویب سائٹ آپکی مدد کر رہی ہے۔ شکریہ