Home » Chemical Engineering Quiz » Chemical Engineering Basics Quiz 7

Chemical Engineering Basics Quiz 7

0%
0

Chemical Engineering Basics Quiz 7

1 / 50

L.D. (Linz-Donawitz) converter is used in the production of______?

2 / 50

Inertial forces are obtained, when the elastic forces are multiplied by _______ number?

3 / 50

M10 index of coke indicates its______?

4 / 50

Increase in the entropy of a system represents the_______?

5 / 50

Maximum amount of thermal radiation is emitted at all wavelengths at any specified temperature by a/an _______ body?

6 / 50

Magnesium is present in_____?

7 / 50

LVDT used for displacement measurement is a/an ________ Transducer?

8 / 50

Melting point & boiling points of liquid oxygen are respectively ? 218.8?C & ? 183?C, while the same for liquid nitrogen is ? 210?C & ? 195.8?C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8 ?

9 / 50

Lead is poured into the joints between two _____ pipes?

10 / 50

Materials having resistivity ranging from 1 to 100 ohm. cm is termed as_____?

11 / 50

Methyl orange indicator turns_______?

12 / 50

Metallic surveying tapes are made of ______ which has a low co-efficient of expansion & enough strength ?

13 / 50

Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is _________ mm?

14 / 50

Joule-Thomson co-efficient is the ratio of_________?

15 / 50

Metalloids_________?

16 / 50

Limestone addition in the blast furnace is done to flux ________ present in the raw materials?

17 / 50

In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet ?

18 / 50

Maximum permissible sulphur content in steel is _______ percent ?

19 / 50

Latent heat of dry steam at atmospheric pressure is 539 Kcal/kg; which ______ with increase in the pressure of steam?

20 / 50

Isotropic materials have the same _________ in all directions?

21 / 50

Lead is poured into the joint between two _______ pipes?

22 / 50

Lead is poured into the joint between two ________ pipes ?

23 / 50

Material of construction of foundry crucible is __________?

24 / 50

Insulation of liquid surface can be achieved by ______ on top of its surface?

25 / 50

Lead pencil contains______?

26 / 50

Large scale fire on fuel gas line is normally extinguished by_________?

27 / 50

Maximum change in the hardness of martensite occurs in the carbon content range of ______ percent in steel?

28 / 50

Increasing the carbon content of steel__________?

29 / 50

Increase in temperature, in general results in the______?

30 / 50

Iron content in Indian iron ore is about __________ percent?

31 / 50

Metal shots used in shot blasting are made of ________?

32 / 50

Large diameter reinforced cement concrete (RCC) pipes are generally joined by ______ joint ?

33 / 50

Maximum hardenability of steel depends upon its_________?

34 / 50

Lead is added to 60:40 brass primarily to improve__________?

35 / 50

Machinability of hard alloys and tool steels is improved by_______?

36 / 50

Main constituent of bone ash is______?

37 / 50

Matte smelting is used in the extraction of_______?

38 / 50

Increasing sulphur content in pig iron tends to make it _________?

39 / 50

Internal energy of a gas obeying Van-Der-Waals equation of state, [p + (a/v2)] (V ? b) = RT, depends upon its_____?

40 / 50

Laser is a device to produce_____?

41 / 50

Limestone is added in the blast furnace (during pig iron manufacture) to________?

42 / 50

Load cells used for the measurement of weight has_______?

43 / 50

Liquor poisoning generally occurs due to the presence of ________ in it?

44 / 50

Mho?s scale of hardness, which consists of 10 standard minerals is used for the measurement of ________ hardness?

45 / 50

Liquid nitrogen containers can be made from _____?

46 / 50

Midrex process of sponge iron production uses reformed natural gas as the reducing agent, which uses iron ore in the form of__________?

47 / 50

Materials having _________ lattice structure are usually the most ductile ?

48 / 50

Maximum permissible air velocity in pipelines is about _______ metre/second ?

49 / 50

Maximum consumption of limestone is in the ______ industry?

50 / 50

In TIG welding, thoriated tungsten electrodes are used, because it ______?

Provide Your Information

Your score is

The average score is 0%

0%

Share on facebook
Facebook
Share on twitter
Twitter
Share on whatsapp
WhatsApp
Chemical Engineering Basics Quiz 1
Chemical Engineering Basics Quiz 2
Chemical Engineering Basics Quiz 3
Chemical Engineering Basics Quiz 4
Chemical Engineering Basics Quiz 5
Chemical Engineering Basics Quiz 6
Chemical Engineering Basics Quiz 8
Chemical Engineering Basics Quiz 9
Chemical Engineering Basics Quiz 10
Chemical Engineering Basics Quiz 11

Help Concept 360 Please. We need 500 Youtube Subscriber. Please Subscribe our Youtube Channel. Click below link to subscribe Please

آپ سے گزارش ہے کہ ہمارے یوٹیوب چینل کوسبسکرائب کر کے ہماری مدد کریں جیسا کہ یہ ویب سائٹ آپکی مدد کر رہی ہے۔ شکریہ