Civil Engineering Quiz 49
1 / 50
If the 20 mm rivets are used in lacing bars, then the minimum width of lacing bar should be_____?
2 / 50
For treating the sewage of a large city, you will recommend________?
3 / 50
The pressure at a point in a fluid will not be same in all the directions when the fluid is_______?
4 / 50
The ratio of the diameter of a circular section and the side of a square section hydraulically equivalent, is___________?
5 / 50
Assertion A : The consumption of water increases with increase in the distribution pressure. Reason R : Higher distribution pressure causes more loss and waste of water. Select your answer according to the coding system given below?
6 / 50
Metacentric height is given as the distance between______?
7 / 50
Which of the following is a scalar quantity ?
8 / 50
Main purpose of mean water training for rivers is_______?
9 / 50
The fundamental factor in the selection of pavement type is_____________?
10 / 50
Minimum compressive strength in N/mm2 for H1 type mortar used for masonry is______?
11 / 50
Duopsony is a market situation where there is/are_____?
12 / 50
Jumper is a tool used for______?
13 / 50
Sensitivity analysis is a study of_________?
14 / 50
Select the correct statement_____?
15 / 50
the column head support a flat slab, is generally kept The diameter of_____________?
16 / 50
The detention period for plain sedimentation water tanks, is usually___________?
17 / 50
What refers to the claim of anyone to ownership ?
18 / 50
The difference of levels between two stations A and B is to be determine. For best results, the instrument station should be______?
19 / 50
The triangular space formed between the extrados and the horizontal line drawn through the crown of an arch is known as____________?
20 / 50
In a simply supported slab, alternate bars are curtailed at_______?
21 / 50
If the direction of projection bisects the angle between the vertical and the inclined plane, then the range of projectile on the inclined plane is_________?
22 / 50
If the eccentricity ratio is more than 1/24, then increase in the permissible stress in the design of wall subjected to eccentric loading as per code is________?
23 / 50
Bearing stiffener in a plate girder is used to_________?
24 / 50
Coherence of two electromagnetic waves takes place if their phase difference is________?
25 / 50
The horizontal angle between the true meridian and magnetic meridian at a place is called_____?
26 / 50
Cant deficiency occurs when a vehicle travels around a curve at________?
27 / 50
If the permissible stress in steel in tension is 140 N/mm2, then the depth of neutral axis for a singly reinforced rectangular balanced section will be__________?
28 / 50
For design, that length of transition curve should be taken which is_____________?
29 / 50
RC-2, MC-2 and SC-2 correspond to______?
30 / 50
Seepage through foundation in an earthen dam is controlled by providing__________?
31 / 50
As applied to staff readings, the corrections for curvature and refraction are respectively The above table shows a part of a level field book. The value of X should be_______?
32 / 50
For providing an Indian type W.C., the R.C. slabs in the toilet portion_________?
33 / 50
Maximum daily traffic capacity of bituminous pavements is_____?
34 / 50
A masonry dam (density = 20,000 N/m3) 6 m high, one metre wide at the top and 4 m wide at the base, has vertical water face. The minimum stress at the base of the dam when the reservoir is full, will be______________?
35 / 50
Pick up the correct statement from the following?
36 / 50
The alum, when added as a coagulant in water______?
37 / 50
Pick up the item of work not included in the plinth area estimate_____?
38 / 50
A free standing brick wall 20 cm thick is subjected to a wind pressure of 75kg/m2. The maximum height of wall from stability consideration is__________?
39 / 50
Pick up the correct statement from the following ?
40 / 50
For a standard 45? fillet, the ratio of size of fillet to throat thickness is______?
41 / 50
The functional depreciation is sometimes called ___________?
42 / 50
The main disadvantage of angle nose out parking configuration of aircraft is that the______?
43 / 50
The sewer which collects the discharge from a collecting system and delivers it to a treatment plant, is known____________?
44 / 50
Select the incorrect statement?
45 / 50
Tangent of angle of friction is equal to________?
46 / 50
For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed_______?
47 / 50
As compared to stretcher course, the thickness of joints in header course should be_____________?
48 / 50
Cash money and credit necessary to establish and operate an enterprise are generally called ____________?
49 / 50
The recommended detention period for grit chambers is______?
50 / 50
The design of heel slab of a retaining wall is based on the maximum bending moment due to_____?
Provide Your Information
Your score is
The average score is 0%
Restart quiz
