Dental Materials Quiz 5
1 / 50
The main difference between dental stone and dental plaster is______________?
2 / 50
Age hardening is a process done at______________?
3 / 50
Which of the waxes are derived from the lignite_________________?
4 / 50
Green strength with reference to plaster means_____________?
5 / 50
Best marginal seal is provided by____________?
6 / 50
Which of the following impression material requires a hardener ?
7 / 50
In processing methyl methacrylate, the resin may show porosity if the flask is placed too soon porosity most likely occur_____________?
8 / 50
The chemical used to etch enamel is_______________?
9 / 50
Which is best material for RPD impression_______________?
10 / 50
A rough / Chalky surface of the cast is due to_______________?
11 / 50
About polymerization shrinkage of composite all are true, except______________?
12 / 50
Co-efficient of thermal expansion is highest for_____________?
13 / 50
In Base metal alloys, Corrosion resistance occurs due to___________________?
14 / 50
Gases dissolved in molten metals are liberated when cooled giving rise to________________?
15 / 50
Electrolyte used for plating copper dies is________________?
16 / 50
The melting point of titanium is __________ degree celsius?
17 / 50
As per DNA No. 25, minimum amount of setting expansion required for type V gypsum products_______________?
18 / 50
Localised shrinkage porosity is seen when there________________?
19 / 50
Greening occuring when porcelains are fired on silver free alloys may be attributed to________________?
20 / 50
Which of the following physical property can be used to estimate indirectly the proportional limit of gold alloys ?
21 / 50
Most ideally elastic among the following_______________?
22 / 50
Casting shrinkage is compensated by_______________?
23 / 50
Minimum thickness for type I zinc phosphate cement should be_______________?
24 / 50
The setting of zinc phosphate is accelerated by_____________?
25 / 50
PH of which cement remain below 7 even after 1 month after insertion into the cavity ?
26 / 50
Nickel is added to wrought gold alloys as______________?
27 / 50
Which of the following refractory is used to counteract most of the expansion________________?
28 / 50
The setting time of irreversible hydrocolloids can be decreased by_____________?
29 / 50
The main form of iron carbide found in 18-8 steel________________?
30 / 50
Ability of an orthodontic wire to spring back to its original shape is evaluated by_____________?
31 / 50
Silica sol__________________?
32 / 50
Stages of annealing in order_________________?
33 / 50
Which of the following statement is true regarding lathe cut low Copper silver alloy ?
34 / 50
Stainless steel orthodontic wire can be hardened by________________?
35 / 50
Quartz in investment material is added for_______________?
36 / 50
The relative hardness of elastomere is determined using________________?
37 / 50
Creep value of which of the following is the highest ?
38 / 50
Polysulfide material is routinely not recommended because of_______________?
39 / 50
Porcelain binds to metal in PFM crown by_________________?
40 / 50
Annealing is also known as_______________?
41 / 50
The ? (Beta) hemihydrate of gypsum requires more water to float its powder particles because______________?
42 / 50
Flux used in dental ceramic is________________?
43 / 50
In a metal ceramic crown for a FPD the function of tin, indium which are readily oxidized minor constituents is to________________?
44 / 50
Percentage of tin in low copper alloy is______________?
45 / 50
All of the following is used as accelerator in zinc oxide eugenol cement except_______________?
46 / 50
Percentage of gold in high noble alloy is______________?
47 / 50
Gypsum is used for________________?
48 / 50
For photo-curing the composite resin the light source______________?
49 / 50
Brush heap structure is found in______________?
50 / 50
Which one of the following is used as filler in composite resins ?
Provide Your Information
Your score is
The average score is 56%
Restart quiz
