Mechanical Engineering Quiz 10
1 / 50
Which is correct statement about reaction time for autoignition of fuel and the fuel air ratio__________________?
2 / 50
Inertia force acts___________________?
3 / 50
Monte Carlo solutions in queuing theory are extremely useful in queuing problems_________________?
4 / 50
Thermal conductivity of wood depends on_______________?
5 / 50
Which of the following is independent of sales forecast______________?
6 / 50
The composition of silver solder is ___________________?
7 / 50
The efficiency of a nuclear power plant in comparsion to a conventional thermal power plant is________________?
8 / 50
Blast furnace produces following by reduction of iron ore_______________?
9 / 50
A trolley wire weighs 1.2 kg per meter length. The ends of the wire are attached to two poles 20 meters apart. If the horizontal tension is 1500 kg find the dip in the middle of the span___________________?
10 / 50
As a result of detonation in an I.C engine, following parameter attains very high value _____________________?
11 / 50
In order that a cycle be reversible, following must be satisfied ________________?
12 / 50
In which case the air-fuel ratio is likely to be maximum _________________?
13 / 50
Petrol is distilled at a temperature in range of__________________?
14 / 50
The ultimate tensile strength of low carbon steel by working at a high strain rate will_________________?
15 / 50
I.S. specifies following total number of grades of tolerances__________________?
16 / 50
Which tool is used to measure gap size in a rough alignment?
17 / 50
Amongst the following, the fissionable materials are________________?
18 / 50
The metallic structure of mild steel is_________________?
19 / 50
Elastic nut is a locking device in which__________________?
20 / 50
A diesel engine as compared to petrol engine (both running ar rated load) is ____________________?
21 / 50
Kinematic viscosity is equal to_________________?
22 / 50
Structural steel contains following principal alloying elements__________________?
23 / 50
Turn buckle has____________________?
24 / 50
Wrought iron is________________?
25 / 50
Kinematic pairs are those which have two elements that ______________?
26 / 50
Pick up the correct statement about relationship between various floats______________________?
27 / 50
A neutral flame is obtained by supplying___________________?
28 / 50
In actual machines_____________________?
29 / 50
A diesel engine has_________________?
30 / 50
Inventory control in production, planning and control aims at________________?
31 / 50
In PERT analysis, critical path is obtained by joining events having___________________?
32 / 50
In axial flow fans and turbines, fluid enters and leaves as follows________________?
33 / 50
Solids and liquids have___________________?
34 / 50
Which of the following parameters is constant for a mole for most of the gases at a given temperature and pressure___________________?
35 / 50
The Ackermann steering mechanism is preferred to the Davis type in automobiles because____________________?
36 / 50
On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be___________________?
37 / 50
The pour point of diesel oil must be_________________?
38 / 50
The compression ratio in a gas turbine is of the roder of____________________?
39 / 50
Auto-ignition reaction time for petrol engine first decreases with increase in fuel air ratio, reaches a minimum value and then increases with subsequent increase in fuel air ratio. The minimum value occurs in the region of________________?
40 / 50
Efficiency of a riveted joint is the ratio of its strength (max. load it can resist without failure) to the strength of the unpunched plate in_________________?
41 / 50
Corioli?s component of acceleration exists whenever a point moves along a path that has________________?
42 / 50
In vapor compression refrigeration system, refrigerant occurs as liquid between_________________?
43 / 50
Pick up the wrong statement?
44 / 50
Pulverized fuel is used for___________________?
45 / 50
The normal stress is same in all directions at a point in a fluid_______________?
46 / 50
A key is subjected to side pressure as well at shearing forces. These pressures are called_________________?
47 / 50
Connecting rod is usually made of_________________?
48 / 50
Francis turbine is best suited for_____________________?
49 / 50
Gnatt charts are used for_________________?
50 / 50
Free air is the air at________________?
Provide Your Information
Your score is
The average score is 60%
Restart quiz