Home » Mechanical Engineering Quiz » Mechanical Engineering Quiz 2

Mechanical Engineering Quiz 2

0%
12

Mechanical Engineering Quiz 2

1 / 50

One time measurement unit (TMU) in method time measurement system equals______________?

2 / 50

When two plates are butt together and riveted with cover plates with two rows of rivets, the joi;it is known as ___________________?

3 / 50

The spark plug gap is normally maintained at________________?

4 / 50

If V, U and Vr represent the absolute velocity of fluid, velocity of blade, and relative velocity of fluid, and suffix i and o stand for entry and exit conditions, then in a rotary machine whose degree of reaction is unity______________?

5 / 50

The criterion of the thermodynamic efficiency for rotary compressor is_________________?

6 / 50

More than one stage will be preferred for reciprocating compressor if the delivery pressure is more than____________________?

7 / 50

A semi-circular disc rests on a horizontal surface with its top flat surface horizontal and circular portion touching down. The coefficient of friction between semi-cricular disc and horizontal surface is i. This disc is to be pulled by a horizontal force applied at one edge and it always remains horizontal. When the disc is about to start moving, its top horizontal force will____________________?

8 / 50

The probability distribution of project completion in PERT follows following distribution_________________?

9 / 50

In forced circulation type boiler__________________?

10 / 50

The center of percussion of the homogeneous rod of length L suspended at the top will be___________________?

11 / 50

With increase in load, radiant super heater has____________________?

12 / 50

In testing a material for endurance strength, it is subjected to_______________________?

13 / 50

Centrifugal pump is started with its delivery valve __________________?

14 / 50

In grey cast iron, carbon is present in the form of____________________?

15 / 50

Gas turbine works on______________?

16 / 50

Amorphous material is one___________________?

17 / 50

The following type of nut is used with alien bolt____________________?

18 / 50

White cast iron__________________?

19 / 50

Which of the following materials is most elastic_________________?

20 / 50

Ram compression in turbojet involves____________________?

21 / 50

The value of the product of molecular weight and the gas characteristic constant for all the gases in M.K.S. unit is______________________?

22 / 50

Thermal diffusivity is ____________________?

23 / 50

Isotropic materials are those which have the same ____________________?

24 / 50

Which of the following substance will have same percentage in both proximate and ultimate analysis___________________?

25 / 50

Frictional force encountered after commencement of motion is called ___________________?

26 / 50

A material is known as allotropic or polymorphic if it __________________?

27 / 50

The feed check valve is used in order to ______________________?

28 / 50

The specific heat of superheated steam in kcal/kg is generally of the order of___________________?

29 / 50

A hmh flame speed is obtained in diesel engine when air fuel ratio is_______________?

30 / 50

The buckling load for a given material depends on___________________?

31 / 50

In a refrigeration cycle, the flow of refrigerant is controlled by___________________?

32 / 50

An alien bolt is___________________?

33 / 50

Condensing temperature in a refrigerator is the temperature_________________?

34 / 50

The unit?of universal gas constant is___________________?

35 / 50

The ratio of elongation in a prismatic bar due to its own weight (W) as compared to another similar bar carrying an additional weight (W) will be _________________?

36 / 50

The unit of overall coefficient of heat transfer is___________________?

37 / 50

Work study is done with the help of_______________?

38 / 50

Which of the following is false statement in respect of differences between machine and structure___________________?

39 / 50

The elasticity of various materials is controlled by its___________________?

40 / 50

Which of the following can be regarded as gas so that gas laws could be applicable, within the commonly encountered temperature limits ?

41 / 50

The rating of a diesel engine, with increase in airintlet temperature, will ___________________?

42 / 50

The maximum strain energy that can be stored in a body is known as________________?

43 / 50

Three different weights fall from a certain height under vacuum. They will take______________?

44 / 50

The height of chimney in a power plant is governed by__________________?

45 / 50

A jet engine works on the principle of conservation of____________________?

46 / 50

In an isothermal process, the internal energy of gas molecules________________?

47 / 50

The thrust on the rotor in a centrifugal compressor is produced by________________?

48 / 50

Which of the following disciplines provides study of relative motion between the parts of a machine______________?

49 / 50

A supercritical boiler is one that operates above the pressure and temperature of following values_____________________?

50 / 50

Forces are called coplanar when all of them acting on body lie in __________________?

Provide Your Information

Your score is

The average score is 75%

0%

Share on facebook
Facebook
Share on twitter
Twitter
Share on whatsapp
WhatsApp
Mechanical Engineering Quiz 1
Mechanical Engineering Quiz 3
Mechanical Engineering Quiz 4
Mechanical Engineering Quiz 5
Mechanical Engineering Quiz 6
Mechanical Engineering Quiz 7
Mechanical Engineering Quiz 8
Mechanical Engineering Quiz 9
Mechanical Engineering Quiz 10
Mechanical Engineering Quiz 11

Help Concept 360 Please. We need 500 Youtube Subscriber. Please Subscribe our Youtube Channel. Click below link to subscribe Please

آپ سے گزارش ہے کہ ہمارے یوٹیوب چینل کوسبسکرائب کر کے ہماری مدد کریں جیسا کہ یہ ویب سائٹ آپکی مدد کر رہی ہے۔ شکریہ