Mechanical Engineering Quiz 24
1 / 50
Which type of boiler can meet rapid changes of load____________________?
2 / 50
When a piping system is made up primarily of friction head and very little of vertical lift, then pump characteristics should be__________________?
3 / 50
The inlet value of a four stroke cycle I.C engine remains open for nearly___________________?
4 / 50
Pick up the correct statement from the following?
5 / 50
It is required to produce large amount of steam at low pressure. Which boiler should be used ?
6 / 50
Mechanical equivalent of heat for 1 kcal or Joule?s equivalent is equal to_________________?
7 / 50
Two systems shall be dynamically equivalent when____________________?
8 / 50
Pressurised water reactor is designed________________?
9 / 50
A typewriter mechanism has 7 number of binary joints, six links and none of higher pairs. The mechanism is________________?
10 / 50
A pressure of 25 m of head of water is equal to_________________?
11 / 50
The capacity of induced draft fan compared to forced draft fan in a boiler is__________________?
12 / 50
Highest pressure encountered in a refrigeration system should be________________?
13 / 50
Unit of thermal conductivity in M.K.S. units is ___________________?
14 / 50
The edges of the plates for cylindrical vessels are usually bevelled to an angle of 80? for_________________?
15 / 50
The function of injector used in small steam plants is to________________?
16 / 50
Which of the following is the unit of kinematic viscosity _________________?
17 / 50
Which of the following organisation is preferred in automobile industry________________?
18 / 50
If both Stirling and Carnot cycles operate within the same temperature limits, then efficiency of Stirling cycle as compared to Carnot cycle___________________?
19 / 50
Machine screws are________________?
20 / 50
The force acting along the circumference will cause stress in the walls in a direction normal to the longitudinal axis of cylinder; this stress is called___________________?
21 / 50
The overall isothermal eiffciency of compressor is defined as the ratio of_______________?
22 / 50
It equal and opposite forces applied to a body tend to elongate it, the stress so produced is called______________________?
23 / 50
Cupola produces following material__________________?
24 / 50
A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm2 and a volume of 0.039 m3 at 150 kg/cm2. The bulk modulus of elasticity of liquid is___________________?
25 / 50
The size of a boiler drum in pulverised fuel fired boiler,as its size and capacity, (steam pressure and flow ratings) increase __________________?
26 / 50
Klein?s construction can be used when_________________?
27 / 50
Which of the following is a case of steady state heat transfer ___________________?
28 / 50
An event is indicated on the network by_________________?
29 / 50
For standard coarse threads of nut, the threads will be as strong in failure by shear as the bolt in tension, if the height of nut (h) is approximately________________?
30 / 50
Which of the following is a fire tube boiler________________?
31 / 50
In fast breeder reactors___________________?
32 / 50
The flow in which the velocity vector is identical in magnitude and direction at every point, for any given instant, is known as________________?
33 / 50
The ratio of specific weighf/h.p. of gas turbin and I.C engines may be typically of the order of_______________________?
34 / 50
Mass flow ratio of NH3 in comparison to Freon-12 for same refrigeration load and same temperature limits is of the order of___________________?
35 / 50
The critical activity has____________________?
36 / 50
Machining properties of steel are improved by adding___________________?
37 / 50
Cavitation will begin when__________________?
38 / 50
Euler?s dimensionless number relates the following__________________?
39 / 50
Pick up the false statement ?
40 / 50
As the value of index ??? is decreased, the volumetric efficiency will___________________?
41 / 50
The latent heat of steam at pressures greater than atmospheric in comparison to latent heat at atmospheric pressure is__________________?
42 / 50
Scavenging is usually done to increase__________________?
43 / 50
Deaeration of feed water is carried out because it reduces ____________________?
44 / 50
Clearance volume in actual reciprocating compressors is essential __________________?
45 / 50
For economical operation of a nuclear plant__________________?
46 / 50
According to Clausis statement of second law of thermodynamics___________________?
47 / 50
Method of governing used in petrol engine is________________?
48 / 50
The percentage of carbon in low carbon steel is__________________?
49 / 50
The absolute acceleration of any point P in a link about center of rotation 0 is___________________?
50 / 50
In Vicker?s hardness testing, the pyramid indentor apex is__________________?
Provide Your Information
Your score is
The average score is 59%
Restart quiz