Mechanical Engineering Quiz 34
1 / 50
The ultimate analysis of fuel lists _____________________?
2 / 50
Foundry crucible is made of_________________?
3 / 50
The property of fluid by virtue of which it offers resistance to shear is called________________?
4 / 50
Statistical quality control techniques are based on the theory of___________________?
5 / 50
The power available for take off and climb in case of turbojet engine as compared to reciprocating engine is ___________________?
6 / 50
Isothermal compression though most efficient, but is not -practicable because_________________?
7 / 50
A 75 cc engine has following parameter as 75 cc ___________________?
8 / 50
Casting of a centrifugal pump is designed so as to minimize________________?
9 / 50
The capacity of compressor will be highest when its intake temperature is___________________?
10 / 50
The simplex method is the basic method for__________________?
11 / 50
Balls for ball bearings are made of_________________?
12 / 50
The output of a diesel engine can be increased without increasing the engine revolution or size in following way_________________?
13 / 50
Emissivity of a white polished body in comparison to a black body is________________?
14 / 50
Heating value of fuel used is as on fired basis. If it is reported for dry or moisture free fuel, then latter should be multiplied by the following factor to correct for as fired value ___________________?
15 / 50
Inter cooling in compressors__________________?
16 / 50
The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is______________________?
17 / 50
Ignition timing of a multicylider petrol engine can be adjusted by_________________?
18 / 50
The safe twisting moment for a compound shaft is equal to the _________________?
19 / 50
Addition of copper to aluminium results in_____________________?
20 / 50
The work ratio of simple gas turbine cycle depends on_________________?
21 / 50
Rupture stress is________________?
22 / 50
To transmit power from one rotating shaft to another whose axes are neither parallel nor intersecting, use__________________?
23 / 50
PERT stands for k (fit) project evaluation and review technique__________________?
24 / 50
The termal efficiency of a petrol engine at design load is around_________________?
25 / 50
The major axis of elliptical manholes on the shell should be provided___________________?
26 / 50
The basis for measuring thermodynamic property of temperature is given by___________________?
27 / 50
Water contained in a beaker can be made to boil by passing steam through it__________________?
28 / 50
Lower pairs are those which have___________________?
29 / 50
The unit of length in S.I. units is________________?
30 / 50
The leaks in a refrigeration system using Freon are detected by____________________?
31 / 50
Rivets are generally specified by_______________?
32 / 50
For an irreversible gas turbine cycle, the efficiency and work ratio both depend on___________________?
33 / 50
In the case of compression ignition engine, the %age of CO in exhaust gases is________________?
34 / 50
The vapour pressure over the concave surface is______________________?
35 / 50
Tensile strength of a mild steel specimen can be roughly predicted from following hardness test_________________?
36 / 50
Efficiency of a Carnot engine is given as 80%. If the- cycle direction be reversed, what will be the value of COP of reversed Carnot cycle_________________?
37 / 50
In the equation of virtual work, following force is neglected_______________________?
38 / 50
Which of the following layouts is suited to job production__________________?
39 / 50
The flow in which conditions do not change with time at any point, is known as_________________?
40 / 50
Enriched uranium is one in which__________________?
41 / 50
The forces, which meet at one point, but their lines of action do not lie in a plane, are called_________________?
42 / 50
Which is the false statement about the properties of instantaneous center____________________?
43 / 50
Boyle?s law i.e. pV = constant is applicable to gases under ___________________?
44 / 50
High specific speed of turbine implies it is__________________?
45 / 50
The crest diameter of a screw thread is same as _____________________?
46 / 50
In an ideal machine, the output as compared to input is_______________?
47 / 50
Temperature of gases at end of compression as compared to exhaust gases in a gas turbine is_________________?
48 / 50
A riveted joint in which the number otrivets decrease from innermost to outer most row is called__________________?
49 / 50
Normal heptane_______________?
50 / 50
All the terms of energy in Bernoulli?s equation have dimension of_______________?
Provide Your Information
Your score is
The average score is 56%
Restart quiz
