Home » Mechanical Engineering Quiz » Mechanical Engineering Quiz 5

Mechanical Engineering Quiz 5

0%
6

Mechanical Engineering Quiz 5

1 / 50

Separators in compressor installations are located_____________________?

2 / 50

The specific output per kg mass flow rate of a gas turbine (having fixed efficiencies of compressor and turine and fixed higher and lower temperature) with increase in pressure ratio will___________________?

3 / 50

Gas turbines for power generaion are normally used___________________?

4 / 50

The dry saturated steam at very low pressure, (5-10 kg/cm2) when throttled to atmosphere will become________________?

5 / 50

Vapor compression refrigeration is some what like ____________________?

6 / 50

Bell metal contains_____________________?

7 / 50

Fatigue strength can be increased by__________________?

8 / 50

Cam angle is defined as the angle_________________?

9 / 50

If overhead clearance is less, then the following type of engine should be selected__________________?

10 / 50

The vloumetric efficiency of compressor with increase in compression ratio will ___________________?

11 / 50

A particle inside a hollow sphere of radius r, having coefficient of friction -rr can rest upto height of___________________?

12 / 50

Guest?s theory of failure is applicable for following type of materials_________________?

13 / 50

According to Kennedy?s theorem, if three bodies have plane motions, their instantaneous centers lie on___________________?

14 / 50

Adiabatic process is________________?

15 / 50

A flywheel on a motor goes from rest to 1000 rpm in 6 sec. The number of revolutions made is nearly equal to_________________?

16 / 50

The value of modulus of elasticity for mild steel is of the order of________________?

17 / 50

The pistons are usually given a coating such as tin plating in order to________________?

18 / 50

Pick up the correct statement about giving up of heat from one medium to other in ammonia absorption system ?

19 / 50

Tensile strength of a material is obtained by dividing the maximum load during the test by the_________________?

20 / 50

A metal with specific gravity of o floating in a fluid of same specific gravity a will____________________?

21 / 50

Value engineering aims at finding out the________________?

22 / 50

Higher pairs are those which have_________________?

23 / 50

Super heating in a refrigeration cycle __________________?

24 / 50

A cycle consisting of two adiabatics and two constant pressure processes is known as___________________?

25 / 50

The building up of worn and uridersized parts, subjected to repeated loads by electroplating is_____________________?

26 / 50

In turbo fan engine, the jet velocity as compared to turbo-jet engine is_________________?

27 / 50

Surface energy per unit area of a surface is numerically equal to _____________________?

28 / 50

The upper surface of a weir over which water flows is known is_____________________?

29 / 50

T Jie horse power transmitted by a belt is dependent upon _________________?

30 / 50

Brayton cycle consists? of following four processes____________________?

31 / 50

Piston rings are usually made of___________________?

32 / 50

For low speed operation or for idling in petrol engines, the engine requirements are for_______________?

33 / 50

Which of the following is the locus of a point that moves in such a manner that its distance from a fixed point is equal to its distance from a fixed line multiplied by a constant greater than one___________________?

34 / 50

Malleable cast iron _________________?

35 / 50

Which of the following is not an interns combustion engine___________________?

36 / 50

The flow rate in gear pump___________________?

37 / 50

PERT analysis is based on____________________?

38 / 50

The condition of steam in boiler drum is always ___________________?

39 / 50

Thermal efficiency of a thermal power plant is of the order of___________________?

40 / 50

For slow-speed large capacity compressor, following type of valve will be best suited________________?

41 / 50

Pick up the wrong statement about water tube boiler in comparison to fire tube boilers ______________________?

42 / 50

The m.e.p. of a diesel cycle having fixed compression ratio with increase in cut-off will_________________?

43 / 50

A safety valve in a locomotive starts leaking. The leaking medium will be_________________?

44 / 50

According to principle of moments__________________?

45 / 50

The evolution of heat of solution takes place in ammonia absorption plant when _____________________?

46 / 50

The tendency of a liquid surface to contract is due to the following property_____________?

47 / 50

Saving of work done and power by fitting an air vessel to single acting reciprocating pump is of the order of__________________?

48 / 50

Kinetic theory of gases assumes that the collisions between the molecules are________________?

49 / 50

The water tubes in a babcock and wilcox boiler are__________________?

50 / 50

In a refrigeration system, heat absorbed in comparison to heat rejected is_________________?

Provide Your Information

Your score is

The average score is 64%

0%

Share on facebook
Facebook
Share on twitter
Twitter
Share on whatsapp
WhatsApp
Mechanical Engineering Quiz 1
Mechanical Engineering Quiz 2
Mechanical Engineering Quiz 3
Mechanical Engineering Quiz 4
Mechanical Engineering Quiz 6
Mechanical Engineering Quiz 7
Mechanical Engineering Quiz 8
Mechanical Engineering Quiz 9
Mechanical Engineering Quiz 10
Mechanical Engineering Quiz 11

Help Concept 360 Please. We need 500 Youtube Subscriber. Please Subscribe our Youtube Channel. Click below link to subscribe Please

آپ سے گزارش ہے کہ ہمارے یوٹیوب چینل کوسبسکرائب کر کے ہماری مدد کریں جیسا کہ یہ ویب سائٹ آپکی مدد کر رہی ہے۔ شکریہ