Home » Mechanical Engineering Quiz » Mechanical Engineering Quiz 7

Mechanical Engineering Quiz 7

0%
4

Mechanical Engineering Quiz 7

1 / 50

The diameter of cylindrical shell of the Lancashire boiler is of the order of__________________?

2 / 50

The following is the inversion of slider crank chain mechanism______________________?

3 / 50

In nodular iron, graphite is in the form of_____________________?

4 / 50

The part load efficiency of a carburettor is,___________________?

5 / 50

In standard taper roller bearings, the angle of taper of outer raceway is___________________?

6 / 50

Any point on a link connecting double slider crank chain will trace a ________________?

7 / 50

The ideal efficiency of simple gas turbine cycle depends on________________?

8 / 50

Plutonium is produced________________?

9 / 50

The usual clearance provided in hydrodynamic bearing per mm of diameter of shaft is___________________?

10 / 50

In designing air preheater, the important design consideration is that_________________?

11 / 50

Which of the following is more appropriate for a moderator. One which_________________?

12 / 50

The intensity of stress which causes unit strain is called_______________?

13 / 50

An ideal flow of any fluid must fulfill the following____________________?

14 / 50

The technique for establishing and maintaining priorities among the various jobs of any project is known as___________________?

15 / 50

Vertical lines on pressure-enthalpy chart show constant_______________?

16 / 50

When trying to turn a key into a lock, following is applied _____________________?

17 / 50

Rotary compressor is best suited for_____________________?

18 / 50

The fatigue limit of a material____________________?

19 / 50

Violent sound pulsations within the cylinder of an IC. engine are caused due to_________________?

20 / 50

The maximum temperature in the I. engine cylinder is of the order of ________________?

21 / 50

Basic solution is one which has pH value___________________?

22 / 50

Angle of action of cam is defined as the angle ____________________?

23 / 50

The M.I. of hollow circular section about a central axis perpendicular to section as compared to its M.I. about horizontal axis is__________________?

24 / 50

A slider crank chain consists of following numbers of turning and sliding pairs_________________?

25 / 50

When heat is transferred from one particle of hot body to another by actual motion of the heated particles, it is referred to as heat transfer by ___________________?

26 / 50

The crystal structure of brass is_________________?

27 / 50

According to principle of transmissibility of forces, the effect of a force upon a body is_________________?

28 / 50

The process of diffusion of one liquid into the other through a semi-permeable membrane is called_______________________?

29 / 50

Austenite rs a combination of_________________?

30 / 50

The first method invented for planning projects was________________?

31 / 50

The strain energy stored in a body due to suddenly applied load compared to when it is applied gradually is____________________?

32 / 50

Turbofan engine employs ____________________ ?

33 / 50

Sulphur content of fuels is very important to the plant operators because it____________________?

34 / 50

In open combustion chamber in diesel engines____________________?

35 / 50

In accelerated circulation type boiler________________?

36 / 50

At low temperatures (say 75?C) the notched-bar impact value of steel____________________?

37 / 50

In an isothermal process, the internal energy________________?

38 / 50

Standard time as compared to normal time is_______________?

39 / 50

A single force and a couple acting in the same plane upon a rigid body_________________?

40 / 50

The refrigerant for a refrigerator should have ___________________?

41 / 50

The C.G. of a solid hemisphere lies on the central radius 3r________________?

42 / 50

Form coefficient of spring is _____________________?

43 / 50

In the opposed piston diesel engine, the combustion chamber is located________________?

44 / 50

Depending on the radiating properties, body will be transparent when________________?

45 / 50

The deflection of a cantilever beam under load W is 8. If its width is halved, then the deflection under load W will be________________?

46 / 50

Belt slip may occur due to________________?

47 / 50

Which of the following is not the unit of power ?

48 / 50

The term ?value? in value engineering refers to_______________?

49 / 50

Boiler H.P. is defined as the ________________ ?

50 / 50

The ultimate tensile stress of mild steel compared to ultimate compressive stress is__________________?

Provide Your Information

Your score is

The average score is 79%

0%

Share on facebook
Facebook
Share on twitter
Twitter
Share on whatsapp
WhatsApp
Mechanical Engineering Quiz 1
Mechanical Engineering Quiz 2
Mechanical Engineering Quiz 3
Mechanical Engineering Quiz 4
Mechanical Engineering Quiz 5
Mechanical Engineering Quiz 6
Mechanical Engineering Quiz 8
Mechanical Engineering Quiz 9
Mechanical Engineering Quiz 10
Mechanical Engineering Quiz 11

Help Concept 360 Please. We need 500 Youtube Subscriber. Please Subscribe our Youtube Channel. Click below link to subscribe Please

آپ سے گزارش ہے کہ ہمارے یوٹیوب چینل کوسبسکرائب کر کے ہماری مدد کریں جیسا کہ یہ ویب سائٹ آپکی مدد کر رہی ہے۔ شکریہ